基于分形接触理论的薄板件钻孔夹具定位布局建模

doi:10.13196/j.cims.2021.0476

计算机集成制造系统 ›› 2023, Vol. 29 ›› Issue (12): 4119-4132.DOI: 10.13196/j.cims.2021.0476

基于分形接触理论的薄板件钻孔夹具定位布局建模

杨勃^1,2,庆烁烁^1,2,高峰^1,2,李艳^1,2,王世军^1,2,吴文武^1,2

1.西安理工大学机械与精密仪器工程学院
2.西安理工大学陕西省机械制造装备重点实验室

出版日期:2023-12-31 发布日期:2024-01-10
基金资助:
陕西省自然科学基础研究计划资助项目(2019JQ-384);陕西省教育厅重点实验室资助项目(20JS113)。

Modeling of locating layout of drilling fixture for sheet metal part based on fractal contact theory

YANG Bo^1,2,QING Shuoshuo^1,2,GAO Feng^1,2,LI Yan^1,2,WANG Shijun^1,2,WU Wenwu^1,2

1.School of Mechanical and Precision Instrument Engineering,Xi'an University of Technology
2.Key Lab of Mechanical Manufacturing Equipment of Shaanxi Province,Xi'an University of Technology

Online:2023-12-31 Published:2024-01-10
Supported by:
Project supported by the Natural Science Basic Research Plan in Shaanxi Province,China(No.2019JQ-384),and the Key Laboratory Project of Shaanxi Provincial Education Department,China(No.20JS113).

摘要/Abstract

摘要： 为了提高薄板件钻孔夹具定位布局仿真模型的薄板件变形预测精度,提出一种基于分形接触理论的薄板件钻孔夹具定位布局建模方法。首先采用半弹性接触模型近似代替定位元件与薄板件之间的接触,并通过法向弹簧—阻尼单元模拟接触面的刚度和阻尼特性,然后借助分形接触理论获得定位点接触区域法向接触力与接触刚度、阻尼的关系,接着在通过有限元仿真得到各定位点处的法向接触力的基础上,求解每个定位点处的法向接触刚度与阻尼,最后建立薄板件钻孔夹具定位布局仿真模型,对薄板件钻孔后的变形进行预测。通过平板和曲板两个实例验证了所提建模方法的可行性和有效性。

关键词: 薄板件, 钻孔夹具, 定位布局, 变形, 分形接触

Abstract: To improve the prediction accuracy of the sheet metal part deformation in the simulation model of the drilling fixture location layout for sheet metal part,a fractal contact theory based method for the drilling fixture location layout for sheet metal part was proposed.The semi-elastic contact model was used to approximately replace the contact between the positioning element and the sheet metal part,and the contact stiffness and damping characteristics of contact surface were simulated by the normal spring damping unit.Then,the relationships between the normal contact force and the contact stiffness and damping were obtained by the fractal contact theory.The normal contact force at each location point was gained by finite element simulation and the contact stiffness and damping at each location point are solved.A simulation model of the location layout of the drilling fixture for sheet metal part was established and the sheet metal part deformation after drilling was predicted.The feasibility and effectiveness of the proposed modeling method were verified by two examples of flat plate and curved plate.

Key words: sheet metal part, drilling fixture, locating layout, deformation, fractal contact

中图分类号:

TH112

杨勃, 庆烁烁, 高峰, 李艳, 王世军, 吴文武. 基于分形接触理论的薄板件钻孔夹具定位布局建模[J]. 计算机集成制造系统, 2023, 29(12): 4119-4132.

YANG Bo, QING Shuoshuo, GAO Feng, LI Yan, WANG Shijun, WU Wenwu. Modeling of locating layout of drilling fixture for sheet metal part based on fractal contact theory[J]. Computer Integrated Manufacturing System, 2023, 29(12): 4119-4132.

[1]	杨朝晖, 高天石, 李崇赫, 贺子力. 基于新一代几何技术规范的装配误差建模[J]. 计算机集成制造系统, 2024, 30(1): 118-128.
[2]	周光辉, 邹永成, 张超, 常丰田, 门松辰. 考虑多维误差的复杂装配过程数字孪生建模方法[J]. 计算机集成制造系统, 2023, 29(6): 1824-1839.
[3]	杨勃, 庆烁烁, 高峰, 李艳. 基于BPNN与PSO的薄板件钻孔夹具定位布局多目标优化[J]. 计算机集成制造系统, 2023, 29(3): 874-886.
[4]	王权, 张建鹏, 王信玮, 杨超锋, 张国亮. 基于复合形法的薄壁注塑件变形预补偿研究[J]. 计算机集成制造系统, 2023, 29(11): 3692-3703.
[5]	潘柏松, 方宽, 文娟, 项涌涌, 翁微妮. 考虑磨损与变形的谐波齿轮精度可靠性分析与优化设计[J]. 计算机集成制造系统, 2022, 28(2): 355-367.
[6]	王志浩, 李洪斌, 孙磊. 空间多姿态下的钻铆托架变形解析与误差补偿[J]. 计算机集成制造系统, 2022, 28(12): 3956-3966.
[7]	谢绍辉,丁龙伟,戴宁,范需,程筱胜. 基于主应力线的软体气动弯曲驱动器设计[J]. 计算机集成制造系统, 2021, 27(3): 663-671.
[8]	罗仕鉴,边泽,张宇飞,陆佳炜,卢世主. 基于形态匹配的产品仿生设计融合[J]. 计算机集成制造系统, 2020, 26(10): 2633-2641.
[9]	张翔,潘旭东,王广林. 钛合金介观尺度铣削表面粗糙度特征分析及工艺优化[J]. 计算机集成制造系统, 2018, 24(第12): 2933-2940.
[10]	杨元,王仲奇,杨勃,李诚,康永刚. 基于SVR的航空薄壁件夹具布局优化预测模型[J]. 计算机集成制造系统, 2017, 23(第6期): 1302-1309.
[11]	韩振宇,王瀚,邵忠喜,富宏亚,姜辉,王伟顺. 基于有限差分法的重型龙门铣床大跨距横梁重力变形曲线计算方法[J]. 计算机集成制造系统, 2016, 22(第6期): 1495-1503.
[12]	赵东平,田锡天,耿俊浩. 面向机构组件装配的偏差源等效分析方法[J]. 计算机集成制造系统, 2016, 22(第4期): 991-999.
[13]	刘思濛,邵晓东,王豆. 一种基于动力学分析的薄壁深腔零件加工变形仿真方法[J]. 计算机集成制造系统, 2016, 22(第10期): 2294-2304.
[14]	王乾俸,张松,陈舟,张宝雷,江诚. 基于指数函数的机床主轴热误差补偿模型[J]. 计算机集成制造系统, 2015, 21(第6期): 1553-1558.
[15]	刘建永,乔立红. 一种考虑零件变形的装配误差计算方法[J]. 计算机集成制造系统, 2015, 21(第1期): 94-100.

基于分形接触理论的薄板件钻孔夹具定位布局建模

Modeling of locating layout of drilling fixture for sheet metal part based on fractal contact theory

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics