基于S型加减速的自适应前瞻NURBS曲线插补算法

• 论文 •

基于S型加减速的自适应前瞻NURBS曲线插补算法

罗钧1，汪俊1，刘学明2，张平2，陈建端2

1.重庆大学光电技术及系统教育部重点实验室，重庆400030；2.国防科技工业5011二级计量站，重庆400050

收稿日期:2013-01-25 修回日期:2013-01-25 出版日期:2013-01-25 发布日期:2013-01-25

Adaptive NURBS interpolation algorithm with look-ahead function based on S-shape acceleration/deceleration

LUO Jun1, WANG Jun1，LIU Xue-ming2,ZHANG Ping2,CHEN Jian-duan2

1.Key Laboratory of Optoelectronic Technology and System, Ministry of Education, Chongqing University, Chongqing 400030, China;2.5011 Two Level Measurement Station of Science Technology and Industry for National Defense, Chongqing 400050, China

Received:2013-01-25 Revised:2013-01-25 Online:2013-01-25 Published:2013-01-25

摘要/Abstract

摘要： 为实现加工过程中进给速度和加速度的平滑过渡，减小其突变时对机床的冲击，更好地保证加工精度，提出一种基于S型加减速的前瞻自适应非均匀有理B样条曲线插补算法。该算法根据弓高误差的要求，确定出各插补点的自适应进给速度及位置参数，然后找出速度改变点及其等速区间。为避免相邻速度改变点间加减速过程的互相影响，分别在插补前瞻距离和预前瞻距离内，根据设备允许的最大加速度、加加速度以及S型加减速算法对各速度改变点参数进行分析，筛选出决定加减速过程的关键点，再进行S型加减速控制，使进给速度和加速度得以平滑过渡，从而满足机床加减速能力的要求。仿真结果表明，该算法能够满足高速高精度的要求，验证了其可行性。

关键词: 非均匀有理B样条, 进给速度改变点, 前瞻算法, S型加减速算法

Abstract: To realize smooth transition from feed rate to acceleration which could reduce mechanical shock to the machine tools, and to guarantee the machining accuracy, an adaptive Non-Uniform Rational B-Spline (NURBS) curve interpolation algorithm based on S-shape acceleration/deceleration with look ahead function was proposed. According to demand of chord error, the feed rate and location parameters for each interpolation point were defined, and the changed point and constant region of speed were found. To avoid the interaction of acceleration/deceleration process between consecutive speed changed points, the changed points of each speed were analyzed based on permitted algorithm such as maximum acceleration, jerk and S-shape acceleration/deceleration, thus the key point which decided the process of acceleration/deceleration was selected. On this basis, the key point was controlled with S-shape acceleration/deceleration, and the smooth transition from feed rate to acceleration was realized. Thus the machine tools' demand was satisfied. The simulation result showed that the proposed algorithm could satisfied the requirement of high speed and high precision, and its feasibility was also verified.

Key words: non-uniform rational B-spline, feed　rate changed points, look-ahead algorithm, S-shape acceleration/deceleration algorithm

中图分类号:

TP391

罗钧1，汪俊1，刘学明2，张平2，陈建端2. 基于S型加减速的自适应前瞻NURBS曲线插补算法[J]. .

LUO Jun1, WANG Jun1，LIU Xue-ming2,ZHANG Ping2,CHEN Jian-duan2. Adaptive NURBS interpolation algorithm with look-ahead function based on S-shape acceleration/deceleration [J]. .

[1]	吴玉香,王鹏. 基于曲线长度自调整速度方程的非均匀有理B样条插补算法[J]. 计算机集成制造系统, 2019, 25(第9): 2256-2264.
[2]	林旭军,张树有,王进,陆国栋. 可去除自交且具有可调节光顺的非均匀有理B样条等距曲线生成方法[J]. 计算机集成制造系统, 2019, 25(第8): 1920-1926.
[3]	万能,段永吉,杜珂. 考虑制备工艺的功能梯度材料零件设计建模[J]. 计算机集成制造系统, 2018, 24(第4): 946-955.
[4]	刘晓健,张树有,魏栋,王自立. 复杂曲面加工中等距双NURBS刀具路径高效插补方法[J]. 计算机集成制造系统, 2017, 23(第6期): 1286-1295.
[5]	张君,张立强,张守军,张凯. 面向五轴加工的等距双NURBS刀具路径同步插补方法[J]. 计算机集成制造系统, 2015, 21(第6期): 1523-1528.
[6]	刘强,刘焕,周胜凯,李传军,袁松梅. 无速度波动的NURBS曲线二次插补算法原理及其实现[J]. 计算机集成制造系统, 2015, 21(第10期): 2659-2667.
[7]	董海涛,潘海鸿,黄丽宇,陈琳. 一种优化的NURBS曲线插补算法[J]. 计算机集成制造系统, 2014, 20(09): 2172-2177.
[8]	王允森,杨东升,刘荫忠,孙一兰. NURBS插补中的速度规划与参数计算[J]. 计算机集成制造系统, 2014, 20(08): 1896-1902.
[9]	王国勋,舒启林,王军,王宛山. 非均匀有理B样条曲线直接插补进给速度规划[J]. 计算机集成制造系统, 2013, 19(06 ): 1272-1278.
[10]	富宏亚,李茂月,+,刘源，韩振宇. 基于曲率特性的柔性加减速NURBS插补器[J]. , 2012, 18(09): 0-0.
[11]	赵鹏，楼佩煌，刘明灯，胡荣华. 基于NURBS曲线拟合的刀具路径优化方法[J]. , 2011, 17(07): 0-0.
[12]	李际军，徐西铎. 基于平行截面轮廓重构曲面实体算法[J]. , 2011, 17(06): 0-0.
[13]	吴继春，唐小琦，陈吉红，周会成. 一种实时快速NURBS插补算法研究与实现[J]. , 2011, 17(06): 0-0.
[14]	普雄鹰,，刘伟军，赵吉宾. 圆柱螺旋线的NURBS逼近表示[J]. , 2011, 17(06): 0-0.
[15]	陈良骥，冯宪章. 五轴NURBS插补中的速度前瞻控制方法[J]. , 2009, 15(12): 0-0.